工业管线里非常便宜的零件是阀门,非常贵的停机事故也常是它惹的。很多采购为了省几百块混用杂牌,结果密封面半年就拉伤,介质一渗漏,整条产线陪着停。
The cheapest component in industrial pipelines is valves, which often cause the most expensive shutdown accidents. Many purchases mix and match miscellaneous brands in order to save a few hundred yuan, resulting in the sealing surface being pulled and the medium leaking within six months, causing the entire production line to stop.

选阀先别看品牌,先看“介质往哪走”:
When choosing a valve, don't look at the brand first, look at "where the medium goes":
全开全关、大口径干线 → 闸阀,流阻小,但别拿来调流量,半开冲刷密封面必漏;
Fully open and fully close, large-diameter main line → gate valve, with low flow resistance, but do not use it to adjust the flow rate. Half open flushing of the sealing surface will cause leakage;
要节流、耐高压 → 截止阀,记住“低进高出”,装反等于白装;
To throttle and withstand high pressure → stop valve, remember "low in, high out", installation is equivalent to white installation;
频繁启闭、要快切 → 球阀或旋塞阀,浆料和含颗粒介质优先旋塞;
Frequent opening and closing, quick switching → ball valve or plug valve, priority should be given to plug valves for slurry and granular media;
泵出口防倒流 → 旋启式止回阀,它只防倒流,不能当切断阀用。
Pump outlet anti backflow → swing check valve, it only prevents backflow and cannot be used as a shut-off valve.
硬参数一条不能让:压力等级按系统非常高工作压力上浮一档,温度留20℃余量,强腐蚀走衬氟或316L,含硫油气走抗硫锻钢。核电、电站、石化项目,阀体材质报告和型式试验证书建议随货,没证一律退。
One hard parameter cannot be set: the pressure level should be increased by one level according to the maximum working pressure of the system, with a temperature margin of 20 ℃, strong corrosion should be treated with fluorine lining or 316L, and sulfur-containing oil and gas should be treated with sulfur resistant forged steel. For nuclear power, power plants, and petrochemical projects, valve body material reports and type test certificates must be included with the goods, and any certificates without them will be returned.
渠道比型号更关键。“良工”这类老牌子仿货多,下单前让供应商出示授权书、原厂铭牌照片和质保函,别信“工字牌差不多”的话术。区域代理的好处是现货在库、24小时能上门,小批量抢修不用等厂里排产。
The channel is more crucial than the model. There are many imitations of old brands such as "Lianggong". Before placing an order, ask the supplier to provide an authorization letter, a photo of the original factory nameplate, and a warranty letter. Don't believe the saying "the work badge is similar". The advantage of regional agency is that spot goods are in stock, available 24 hours a day, and small batch repairs do not have to wait for the factory to schedule production.
阀门没有“非常好”,只有“非常对”。把工况写清楚再询价,比拿着型号比价靠谱十倍。
There is no 'best' valve, only 'most right'. Writing down the working conditions clearly before inquiring is ten times more reliable than comparing prices based on the model.
本文由良工阀门友情奉献.更多有关的知识请点击:http://www.jnlgvf.com我们将会对您提出的疑问进行详细的解答,欢迎您登录网站留言.
This article is a friendly contribution from Lianggong Valve For more information, please click: http://www.jnlgvf.com We will provide detailed answers to your questions. You are welcome to log in to our website and leave a message