工业采购里,阀门非常容易“买回来装得上、用半年开始漏”。问题不在牌子,在选型逻辑反了:先问良工还是杂牌,没先问介质往哪走、压力温度怎么跳。
In industrial procurement, valves are most prone to "being able to be installed after being bought, but starting to leak after six months of use". The problem is not with the brand, but with the reverse logic of the selection: first ask whether it is a good brand or a miscellaneous brand, without first asking where the medium goes or how the pressure and temperature jump.
按介质分路走
Separate by medium

清水/给排水/楼宇:通用闸阀、平衡阀、柱塞阀,铸铁或铸钢够用,核心看密封和启闭手感;
Clear water/water supply and drainage/building: universal gate valves, balance valves, plunger valves, cast iron or cast steel are sufficient, with a focus on sealing and opening/closing feel;
蒸汽/电站高温高压:电站截止阀、锻钢闸阀,阀体锻钢、密封面堆焊硬质合金,扛热冲击和频繁启停;
Steam/power plant high temperature and high pressure: power plant globe valves, forged steel gate valves, forged steel valve bodies, hard alloy welded sealing surfaces, resistance to thermal shock and frequent start stop;
石化/含硫/料浆:抗硫截止阀、料浆阀,A105+硬化处理,防硫化氢应力开裂、防颗粒冲蚀;
Petrochemical/sulfur-containing/slurry: sulfur resistant shut-off valve, slurry valve, A105+hardening treatment, anti hydrogen sulfide stress cracking, anti particle erosion;
核电/军工:核级闸阀、截止阀、气动泄压阀,带核级电动装置,要抗震鉴定、零外漏、双向密封,不是工业阀加个标;
Nuclear power/military industry: nuclear grade gate valves, globe valves, pneumatic relief valves, equipped with nuclear grade electric devices, must undergo seismic assessment, zero leakage, bi-directional sealing, and not be labeled as industrial valves;
美标出口/外资项目:走API 6D、ASME体系,法兰标准、压力等级(Class 150/300/600)别按国标PN硬套。
American standard export/foreign investment projects: Adopt API 6D, ASME system, flange standard, pressure rating (Class 150/300/600) according to the national standard PN hard sleeve.
功能别串着用
Don't string functions together
闸阀、球阀、蝶阀:通断为主,别长期半开当调节用,密封面冲成锯齿;
Gate valve, ball valve, butterfly valve: mainly for on/off, do not keep it half open for a long time for adjustment, and the sealing surface should be serrated;
截止阀:小流量调节可以,大压差节流仍要配专用调节阀;
Globe valve: Small flow regulation is possible, but special regulating valves are still required for large pressure differential throttling;
旋塞阀:含颗粒、快切断浆料场景好用,别拿去精细节流;
Plug valve: Suitable for scenarios involving particles and fast cutting slurry, do not use it for precise throttling;
止回阀:防倒流,脉动流工况选旋启式要核对阀板形式;
Check valve: for anti backflow and pulsating flow conditions, the rotary opening type should be selected, and the valve plate form should be checked;
安全泄压:稳压器泄压阀、安全阀单独整定,不拿普通阀凑。
Safe pressure relief: The pressure relief valve and safety valve of the stabilizer should be set separately, without using ordinary valves.
参数卡三条线
Parameter card with three lines
压力:公称压力按系统峰值×1.25–1.5余量,别卡着1.6MPa买PN16;
Pressure: The nominal pressure should be based on the system peak value multiplied by 1.25-1.5, with a margin of 1.6MPa. Buy PN16 instead;
温度:碳钢425℃以上强度衰减,高温换铬钼钢/不锈钢,低温-40℃以下走低温钢加长阀杆;
Temperature: Strength attenuation of carbon steel above 425 ℃, high-temperature replacement with chromium molybdenum steel/stainless steel, low-temperature steel with extended valve stem below -40 ℃;
材质:304/316L看氯离子,含硫用低硫磷锻钢,强腐看衬氟/双相钢/哈氏。
Material: 304/316L for chloride ions, low sulfur and phosphorus forged steel for sulfur-containing, fluorine lined/duplex steel/Hastelloy for strong corrosion.
驱动与验收
Drive and acceptance
电动执行器看转矩保护、手动应急、防护等级,易燃易爆区要防爆认证。到货验收:查阀体钢印(压力、口径、材质、炉批号)、壳体试压(水压/气压按标准)、密封试验、核级件要溯源文件。济南本地项目还要盯“工”字牌渠道,防贴牌仿冒,合同写清原厂出库单和质保追溯。
Electric actuators require torque protection, manual emergency, protection level, and explosion-proof certification in flammable and explosive areas. Arrival acceptance: Check the valve body steel seal (pressure, diameter, material, furnace batch number), shell pressure test (water/air pressure according to standards), sealing test, and traceability documents for nuclear grade parts. Local projects in Jinan should also pay attention to the "Gong" sign channel, prevent counterfeit branding, and clearly state the original factory delivery order and quality assurance traceability in the contract.
阀门不是“拧着不漏”的零件,是把“介质—压力—温度—材质—密封—驱动—溯源”焊进管线的控制节点。选型省一步,后面停一次机,损失比差价高十倍。
Valves are not parts that can be tightened without leakage, but rather control nodes that weld "medium pressure temperature material seal drive traceability" into pipelines. Choosing a model saves one step, and stopping the machine once afterwards results in a loss ten times higher than the price difference.