管道一漏就停产?阀门不是“拧着不漏”那么简单

来源:http://www.jnlgvf.com/ 日期:2026-10-19 发布人:创始人

工业管线上,非常不被重视、一出事非常要命的,往往是阀门。泵可以备机,管道可以补焊,但高温高压、易燃易爆介质下的阀门一旦内漏或卡死,轻则停机排障,重则安全事故。很多采购只问“DN多少、压力多少、多少钱”,却忽略了选型底层逻辑。

On industrial pipelines, the valves are often the least valued and most deadly when accidents occur. The pump can be used as a backup and the pipeline can be welded, but if the valve leaks or gets stuck under high temperature, high pressure, flammable and explosive media, it may cause a minor shutdown for troubleshooting or a serious safety accident. Many purchases only ask 'how much DN, how much pressure, how much money', but ignore the underlying logic of selection.

闸阀封面01

先按介质和工况定阀门类型:

First, determine the valve type based on the medium and operating conditions:

清水/给排水:闸阀、蝶阀够用,关断为主,别上核级货烧钱;

Clear water/water supply and drainage: gate valves and butterfly valves are sufficient, mainly for shutdown, do not burn money on nuclear grade goods;

蒸汽/电站高温高压:电站截止阀、锻钢闸阀,密封面要司太立硬质合金,阀杆得抗蠕变;

Steam/power plant high temperature and high pressure: power plant globe valves, forged steel gate valves, sealing surfaces made of Stellite hard alloy, and valve stems resistant to creep;

石化/含硫介质:抗硫截止阀、料浆阀,材质要低硫磷锻钢,密封防硫化氢应力开裂;

Petrochemical/sulfur-containing media: sulfur resistant globe valves, slurry valves, made of low sulfur and phosphorus forged steel, sealed to prevent hydrogen sulfide stress cracking;

核电/军工:核级闸阀、核一级截止阀,要做地震鉴定、辐照老化、零泄漏双向密封,不是“工业阀加个标”就行;

Nuclear power/military industry: Nuclear grade gate valves and nuclear grade globe valves require seismic identification, radiation aging, and zero leakage bi-directional sealing, rather than just adding a label to the industrial valve;

需要远程控制:配多回转/部分回转电动装置,但电机防护等级、转矩保护、手动应急机构一个不能省。

Remote control is required: equipped with multi turn/partial turn electric devices, but the motor protection level, torque protection, and manual emergency mechanism cannot be omitted.

选阀三大隐性坑:

Three hidden pitfalls in valve selection:

只写压力等级不写温度:150LB在200℃和425℃许用压力差一大截;

Only write the pressure rating without temperature: 150LB allows for a large pressure difference between 200 ℃ and 425 ℃;

密封面材质将就:硬碰硬、软碰硬用反了,三个月就冲蚀;

The sealing surface material is not suitable: if used in reverse for hard or soft impacts, it will erode in three months;

渠道不正规:同叫“良工”,老牌厂和贴牌坊差的是探伤报告、壳体强度试验、质保追溯。

Irregular channel: the same name is "good worker". The difference between the old brand factory and the memorial archway is flaw detection report, shell strength test and warranty traceability.

工程采购记住:阀门成本通常只占管线总投资3%–5%,但它决定了另外95%能不能安稳跑。看厂看三样——有没有对应工况业绩、出不出第三方检测、售后能不能24小时到现场。

Engineering procurement: The cost of valves usually only accounts for 3% -5% of the total pipeline investment, but it determines whether the other 95% can run smoothly. Look at the factory and see three things - whether there is corresponding working condition performance, whether third-party testing is available, and whether after-sales service can be on-site within 24 hours.

本文由良工阀门友情奉献.更多有关的知识请点击:http://www.jnlgvf.com我们将会对您提出的疑问进行详细的解答,欢迎您登录网站留言.

This article is a friendly contribution from Lianggong Valve For more information, please click: http://www.jnlgvf.com We will provide detailed answers to your questions. You are welcome to log in to our website and leave a message

热销产品:   执行驱动装置 通用工业阀门 冶金工业阀门 水利水务阀门 石油化工阀门 电力电站阀门 核电军工阀门

上海良工阀门山东济南销售处 网站备案号:鲁ICP备2021030403号-1    电话:15098929951 座机:0531—85816056 地址:济南天桥区历山北路198号国际五金机电城A区412号 
网址:http://www.jnlgvf.com/

【本站图片均由网站所有方提供,部分图片来源于网络,如无意中侵犯了某媒体或个人的知识产权,请来信或来电告之,本网站将立即删除。】