很多人采购阀门,习惯先问“DN多少、PN多少”,真到高温蒸汽管爆法兰、酸碱液把阀座啃穿才明白:型号只是门面,介质和工况才是命门。
Many people purchase valves and are accustomed to asking "what is the DN and PN first". It is not until the flange of the high-temperature steam pipe bursts and the valve seat is gnawed through by acidic and alkaline liquids that they understand: the model is only the facade, and the medium and working conditions are the lifeline.

选阀先按“介质往哪走”分三路:
Select the valve and divide it into three paths according to "where does the medium go":
只要全开全关、不调流量:闸阀流阻非常小,适合清水、油品主干管;但别拿它当调节阀用,半开状态密封面冲刷非常厉害。
As long as it is fully open and fully closed, without adjusting the flow rate: the gate valve has the smallest flow resistance and is suitable for clean water and oil main pipelines; But don't use it as a regulating valve, the sealing surface is most severely eroded in the semi open state.
要微调流量、耐蒸汽:截止阀非常稳,S型流道压损大一点,换来的是线性调节和好修。
To fine tune the flow rate and steam resistance: the globe valve is the most stable, and the S-shaped flow channel has a higher pressure loss, resulting in linear adjustment and good repair.
要零泄漏、快切断:球阀旋转90°到位,燃气、压缩空气管线优选;含颗粒介质别硬上软密封,换金属硬密封或旋塞阀。
To achieve zero leakage and fast cut-off: the ball valve should be rotated 90 ° to the correct position, and gas and compressed air pipelines are preferred; Do not use hard or soft seals for media containing particles, replace with metal hard seals or plug valves.
再看三个容易省错钱的点:
Let's take a look at three easy points to save money on:
温度压力要“降额看”。常温PN16的碳钢阀,到300℃可能只剩PN4的承受能力,高温工况直接升材质或升压力等级。
The temperature and pressure should be 'rated down'. The carbon steel valve with PN16 at room temperature may only have the bearing capacity of PN4 at 300 ℃, and the material or pressure level can be directly increased under high temperature conditions.
腐蚀介质别用201冒充304,也别清水管硬上316L——前者穿孔停产,后者白烧钱。
Do not use 201 as a substitute for 304 for corrosive media, and do not force 316L on the water pipe - the former is perforated and shut down, while the latter is a waste of money.
含颗粒浆料避开流道窄的阀,刀闸阀、旋塞阀、衬胶阀才扛得住磨损。
Particle slurry should avoid valves with narrow flow channels, such as knife gate valves, plug valves, and rubber lined valves, in order to withstand wear and tear.
收货时顺手做三件事:阀体铭牌批号和合格证对得上、法兰密封面无砂眼、1.5倍工作压力水压试压保压10分钟不渗。图纸只标型号的项目,一定要反查阀体材质和密封副,不然“同款DN100”能差出两倍寿命。
When receiving the goods, do three things: match the valve body nameplate batch number and certificate of conformity, ensure that the flange sealing surface has no sand holes, and conduct a pressure test at 1.5 times the working pressure for 10 minutes without leakage. For projects that only indicate the model on the drawing, it is necessary to check the valve body material and sealing pair in reverse, otherwise the "same DN100" can have twice the lifespan difference.
冷知识:阀门本身只占管线总投资的3%–5%,但它出问题带来的停机损失,往往是采购差价的几十倍。
Cold knowledge: Valves themselves only account for 3% -5% of the total pipeline investment, but the downtime losses caused by their problems are often tens of times the purchase price difference.
好阀门不喧宾夺主,它只在每次启闭时安静地把活干完。
A good valve does not overshadow others, it only quietly completes the task every time it is opened or closed.