阀门选型:介质往哪走,决定你该买哪种阀

来源:http://www.jnlgvf.com/ 日期:2026-10-09 发布人:创始人

阀门选型非常常见的错误,是拿着管道口径和压力等级就去询价,忽略了非常根本的一个问题:介质在管道里是怎么流动的。 截断、调节、防止倒流、泄压——不同的流动控制需求,对应的阀门类型完全不同。

The most common mistake in valve selection is to inquire about the diameter and pressure rating of the pipeline, ignoring the fundamental issue of how the medium flows in the pipeline. Cut off, regulate, prevent backflow, and relieve pressure - different flow control requirements correspond to completely different types of valves.

截止阀02

截断介质:闸阀和球阀是主力。

Cut off medium: Gate valves and ball valves are the main force.

闸阀的闸板垂直升降,全开时通道几乎和管道内径一致,流阻出彩小,适合需要完全截断且不频繁操作的场合,比如主干管道的隔离。缺点是闸板与密封面之间的摩擦大,开关费力,不适合频繁操作。球阀的球体旋转90度就能完成开关,操作快、密封好,适合需要快速截断的场景。但球阀的流道是缩径的,流阻比闸阀大,不适合对流量损失敏感的长距离输送。

The gate of the gate valve rises and falls vertically, and when fully opened, the channel is almost the same as the inner diameter of the pipeline, with extremely low flow resistance. It is suitable for situations that require complete cutoff and infrequent operation, such as isolation of main pipelines. The disadvantage is that there is high friction between the gate and the sealing surface, making it difficult to open and close, and not suitable for frequent operation. The ball valve can be opened and closed by rotating the ball 90 degrees, with fast operation and good sealing, suitable for scenarios that require quick cutting. However, the flow channel of ball valves is reduced in diameter and has a higher flow resistance than gate valves, making them unsuitable for long-distance transportation that is sensitive to flow loss.

调节流量:截止阀和调节阀更合适。

Regulating flow: globe valves and regulating valves are more suitable.

截止阀的阀瓣是塞形结构,通过改变阀瓣与阀座的间隙来调节流量,调节特性比闸阀和球阀都好。缺点是流阻大,不适合全开运行。如果管道需要频繁调节流量,选截止阀或专用的调节阀,别用闸阀硬凑——闸阀在半开状态下,闸板会受到介质冲刷,很快就被冲蚀损坏。

The valve disc of the globe valve is a plug shaped structure, which adjusts the flow rate by changing the gap between the valve disc and the valve seat, and has better regulating characteristics than gate valves and ball valves. The disadvantage is that it has high flow resistance and is not suitable for fully open operation. If the pipeline needs to adjust the flow frequently, choose a globe valve or a dedicated regulating valve, and do not use a gate valve that is hard pressed - when the gate valve is in a semi open state, the gate will be washed away by the medium and quickly eroded and damaged.

防止倒流:止回阀是唯一选择。

Preventing backflow: Check valves are the only option.

止回阀靠介质自身的流动来启闭,只允许单向流通。选型时要注意开启压力和关闭速度。开启压力太高,泵的能耗增加;关闭速度太慢,停泵时会产生水锤。升降式止回阀适合垂直管道,旋启式止回阀适合水平管道,选择时要匹配安装方向。

Check valves rely on the flow of the medium itself to open and close, allowing only one-way flow. When selecting, pay attention to the opening pressure and closing speed. The opening pressure is too high, which increases the energy consumption of the pump; The shutdown speed is too slow, which can cause water hammer when stopping the pump. Lift check valves are suitable for vertical pipelines, while swing check valves are suitable for horizontal pipelines. When selecting, the installation direction should be matched.

泄压保护:安全阀和泄压阀不能混用。

Pressure relief protection: Safety valves and pressure relief valves cannot be mixed.

安全阀用于承压设备超压时自动泄放,是强制性安全附件,需要定期校验。泄压阀用于系统压力调节,维持压力稳定。两者的功能和精度要求不同,不能互相替代。

Safety valves are used for automatic relief of overpressure in pressure equipment and are mandatory safety accessories that require regular calibration. Pressure relief valves are used to regulate system pressure and maintain pressure stability. The functions and accuracy requirements of the two are different and cannot be replaced by each other.

材质选择看介质特性,不是看价格。

Material selection depends on the characteristics of the medium, not the price.

水、蒸汽、油品、腐蚀性化工介质,对阀体材质和密封材料的要求完全不同。铸铁阀便宜但耐腐蚀性差,铸钢阀强度高但成本也高,不锈钢阀耐腐蚀但价格贵。介质温度也是关键——高温蒸汽建议用耐高温的密封材料,普通橡胶密封很快老化失效。

Water, steam, oil, and corrosive chemical media have completely different requirements for valve body materials and sealing materials. Cast iron valves are cheap but have poor corrosion resistance, cast steel valves have high strength but high cost, and stainless steel valves are corrosion-resistant but expensive. The temperature of the medium is also crucial - high-temperature steam must be sealed with high-temperature resistant materials, as ordinary rubber seals quickly age and fail.

阀门选型的逻辑很清晰:先确定介质需要截断、调节、防倒流还是泄压,再选对应的阀门类型;然后根据介质特性和温度选材质和密封材料;非常后确认安装方向和操作方式。介质往哪走,决定你该买哪种阀。选对了类型,再谈品牌和价格才有意义。

The logic of valve selection is very clear: first determine whether the medium needs to be cut off, regulated, anti backflow or pressure relief, and then select the corresponding valve type; Then select materials and sealing materials based on the characteristics of the medium and temperature; Finally confirm the installation direction and operation method. The direction of the medium determines which valve you should buy. Choosing the right type makes sense when discussing brand and price.

本文由良工阀门山东销售处友情奉献。更多有关的知识请点击:http://www.jnlgvf.com 我们将会对您提出的疑问进行详细的解答,欢迎您登录网站留言。

This article is a friendly contribution from Lianggong Valve Shandong Sales Office. For more information, please click: http://www.jnlgvf.com We will provide detailed answers to your questions. You are welcome to log in to our website and leave a message.

热销产品:   执行驱动装置 通用工业阀门 冶金工业阀门 水利水务阀门 石油化工阀门 电力电站阀门 核电军工阀门

上海良工阀门山东济南销售处 网站备案号:鲁ICP备2021030403号-1    电话:15098929951 座机:0531—85816056 地址:济南天桥区历山北路198号国际五金机电城A区412号 
网址:http://www.jnlgvf.com/

【本站图片均由网站所有方提供,部分图片来源于网络,如无意中侵犯了某媒体或个人的知识产权,请来信或来电告之,本网站将立即删除。】