一、阀门的安装要求!
1、 Installation requirements for valves!
1、安装阀门前,仔细检查所用阀门的型号、规格是否与设计相符;
1. Before installing the valve, carefully check whether the model and specifications of the valve used are consistent with the design;
2、根据阀门型号和出厂说明,检查阀门是否能在要求的条件下使用;
2. Check whether the valve can be used under the required conditions according to the valve model and factory instructions;
3、起吊阀门时,绳索应系在阀体与阀盖的法兰连接处,不得系在手轮或阀杆上,以免损坏阀杆、阀杆和转向车轮;
3. When lifting the valve, the rope should be tied to the flange connection between the valve body and the valve cover, and should not be tied to the handwheel or valve stem to avoid damaging the valve stem, valve stem, and steering wheel;
4、水平管道安装阀门时,阀杆要垂直向上,不能向下;
4. When installing valves in horizontal pipelines, the valve stem should be vertically upward and not downward;
5、安装阀门时,不允许采用强制配合连接,以免因受力不均而损坏;
5. When installing valves, it is not allowed to use forced fitting connections to avoid damage due to uneven stress;
6、明杆闸阀不宜安装在潮湿的地下场所,以免腐蚀阀杆。
6. Bright stem gate valves should not be installed in damp underground places to prevent corrosion of the valve stem.
二、阀门的保养要求!
2、 Maintenance requirements for valves!
1、安装阀门前将管道中的灰尘、焊渣等杂质清理干净;
1. Clean the dust, welding slag and other impurities in the pipeline before installing the valve;
2、管道连接标准与阀门连接标准一致,使用条件与阀门性能一致。
2. The pipeline connection standard is consistent with the valve connection standard, and the usage conditions are consistent with the valve performance.
3、安装时要详细了解阀门的性能和特点;
3. During installation, it is necessary to have a detailed understanding of the performance and characteristics of the valve;
4、阀门安装空间应人性化,便于维护和维修。
4. The installation space of valves should be humanized, easy to maintain and repair.
5、为避免螺丝、螺栓松动造成漏水,使用前要拧紧每颗螺丝;
5. To avoid water leakage caused by loose screws and bolts, each screw should be tightened before use;
6、使用过程中要注意阀门的介质、压力和温度,以免损坏阀门;
6. Pay attention to the medium, pressure, and temperature of the valve during use to avoid damaging the valve;
良工阀门
Lianggong Valve
7、阀门启闭异常,要查明原因,排除故障,不得采用敲打、折断等方法强行启闭。
7. Abnormal valve opening and closing should be investigated for the cause, and the fault should be eliminated. Forced opening and closing methods such as knocking or breaking should not be used.
8、订货合同中无特殊说明的电动和气动阀门只能在室内垂直安装。
8. Electric and pneumatic valves without special instructions in the purchase contract can only be installed vertically indoors.
9、管道施工完成后,应打开管道内所有阀门,清除残留污物。
9. After the completion of pipeline construction, all valves inside the pipeline should be opened to remove residual dirt.